RadFxSat-2 / Fox-1E Flight Model Arrives at Fox Labs for Testing

by

On March 31st, the RadFxSat-2 / Fox-1E flight model arrived at Fox Labs in Granbury, TX where it will undergo testing prior to launch later this year on the ELaNa XX mission aboard Virgin Orbit’s LauncherOne air-launch-to-orbit system. RadFxSat-2 carries a 30 kHz wide V/u linear transponder and radiation experiments for Vanderbilt University’s Institute for Space and Defense Electronics.

 

RadFxSat-2 / Fox-1E in its Pelican case.

AMSAT Vice-President Engineering Jerry Buxton, N0JY, posted the following video showing off the flight model of RadFxSat-2 / Fox-1E for the first time.

GOLF-TEE and GOLF-1 Selected for NASA’s CubeSat Launch Initiative

by

On March 2, 2018, NASA announced the ninth round of selections for the CubeSat Launch Initiative (CSLI). The first two AMSAT GOLF CubeSats, GOLF-TEE and GOLF-1, were among the 21 missions recommended for selection.

AMSAT must negotiate and execute a Cooperative Research and Development Agreement (CRADA) with NASA for each project to finalize selection. NASA anticipates a sufficient number of launch opportunities but does not guarantee that all recommended payloads will be launched.

GOLF-TEE (Technology Evaluation Environment) will serve as a rapidly deployable Low Earth Orbit (LEO) testbed for technologies necessary for a successful CubeSat mission to a wide variety of orbits.

AMSAT Vice-President Engineering Jerry Buxton, N0JY, said “The GOLF-TEE project tees off the next phase of our CubeSat program. GOLF-TEE provides AMSAT hardware and knowledge for Attitude Determination and Control (ADAC) capability and the opportunity to develop a 3U spaceframe with deployable solar panels that can be used in LEO or HEO missions, two of the major systems required in future GOLF and HEO missions.” Ragnarok Industries developed the attitude control system for the Lunar Heimdallr 6U CubeSat, a NASA Cube Quest Challenge finalist.

GOLF-TEE provides the opportunity for rapid deployment and on orbit testing of the AMSAT’s Advanced Satellite Communications and Exploration of New Technology (ASCENT) program’s technology, including radiation tolerant transponder and Integrated Housekeeping Unit (IHU) technologies that will lead the way for low cost commercial off-the-shelf (COTS) systems that can function in the MEO and HEO radiation environments. GOLF-TEE will also carry a Fox-1E design V/u linear transponder and RadFx (Radiation Effects) experiment for Vanderbilt University.

GOLF-TEE and the GOLF program will provide for the development of “Five and Dime” Field-Programmable Gate Array Software Defined Radio (FPGA SDR) transponders for use on a variety of missions and orbits.

The target date for launch of GOLF-TEE is 4Q 2019.

GOLF-1 will serve as a follow-on mission, also to LEO. Launch is targeted for 2020-2021.

GOLF-1 will require a de-orbiting plan that is in compliance with NASA’s NPR 8715.6 NASA Procedural Requirements for Limiting Orbital Debris in order to be manifested on a launch, due to the high altitude AMSAT has requested.

Please consider a donation to the AMSAT GOLF program for development, construction, and testing of the GOLF-TEE and GOLF-1 CubeSats. Donate at https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=STK27W4G9RMLC. Checks may be mailed to AMSAT, 10605 Concord St. #304, Kensington, MD 20895-2526.

Why is there so much TLE confusion when new Cubesats are launched?

by

Every time a CubeSat gets launched, there is some confusion on what TLEs should be used.   This is the result of the process of launching a new amateur CubeSat with other CubeSats, often several dozen at a time.  We then start the  process of determining which object in a “flock” of CubeSats  is associated with a particular spacecraft.

Pre-launch TLEs that are calculated based on the expected orbit are usually supplied by the launch provider. Pre-launch TLEs are used until post-launch TLEs (for the group of objects that your satellite is in) are released from the US Department of Defense Joint Space Operations Center (JSpOC) based on observations made with cameras and radars.

There is a a 5 to 10 day period of tracking a group of CubeSats until they separate enough to isolate the one of interest. By observing the Doppler shift on transmissions from a particular satellite against the calculated Doppler shift from all candidate object TLEs, we can positively associate an object with a particular satellite. In the case of AMSAT satellites, we then advise JSpOC which object number is “ours”.

Finally, an individual satellite and its associated TLEs are determined and we settle down to an single, accurate, reliable set of TLEs … and all the other “best guesses” go away, although they may be still floating around on the Internet. But, there are so many variables  – did you launch on time, did you get released on time, has the group your CubeSat is in separated enough to identify your satellite, etc. that the process that can be both confusing and annoying at the same time.

AMSAT strives to minimize confusion when distributing TLEs.  Dummy object numbers are used for pre-launch TLEs since final object numbers cannot be assigned yet.    Immediately post launch we may post candidate objects with generic names like “OBJECT C”.    Finally, when positive association between an object number and a spacecraft is made, we will use the common name of the satellite.   We always recommend using TLEs from the Keps mailing list or the current bulletin or bare elements from the AMSAT web site.

 

by Ray Hoad
WA5QGD
Orbital Elements Manager

 

 

FoxTelem Version 1.06 Released

by

​I am releasing version 1.06 of FoxTelem today.  This release addresses several defects and instabilities in FoxTelem 1.05 and earlier.  It also introduces a new Earth Plot that allows any telemetry value to be plotted as a heat map against a map of the earth.  For more details about the Earth Plot and some example plots, you can read a quick tutorial that I have written here:
http://www.g0kla.com/workbench/2018-01-26.php

As always, let me know if you see any issues or log them on Github at https://github.com/ac2cz/FoxTelem/issues

KEY CHANGES
~~~~~~~~~~~
* EARTH PLOTS allow you to plot any telemetry value as a heat map on a map of the earth
* Allow graphs and telemetry results to be searched with UTC dates and for ranges of uptime/dates
* Allow stepping through the telemetry with up/down arrows
* Prevent hang when decoder starts if FCD returns an error
* Fixed bug where TLEs were not updated in the name is changed in the spacecraft settings window
* Fixed crashes introduced in 1.05 release
* Display all HERCI High Speed payloads when Raw Byte Payloads shown.
* Fix bug where missing TLE disables spacecraft from being tracked at all
* Fixes bug where DDE connection to SatPC32 fails with European decimal point format
* Add MPPT calibration values for Fox-1D
* Improved the RF signal measurements
* Improved the Find Signal algorithm
* Space graph labels more evenly
* Put the spacecraft tabs in FoxId order

And many other bug fixes. Full list of changes here:
https://github.com/ac2cz/FoxTelem/milestone/3?closed=1

You can download the latest version of the program from:

​