[amsat-bb] Re: [AMSAT-BB] 145 MHz IF on V/s?
Gary "Joe" Mayfield
gary_mayfield at hotmail.com
Sat May 17 21:09:59 PDT 2008
There are many ways to skin the cat... As stated the S-Band down on AO-51
is very easy to work with. The other non-interfering easy and cheaper way
to do it on AO-13 or AO-40 was to simply tune until you found the beacon and
then do everything based your offset from the beacon.
From: amsat-bb-bounces at amsat.org [mailto:amsat-bb-bounces at amsat.org] On
Behalf Of Anthony Monteiro
Sent: Saturday, May 17, 2008 2:40 PM
To: K & R Yoksh; amsat-bb at amsat.org
Subject: [amsat-bb] Re: [AMSAT-BB] 145 MHz IF on V/s?
At 09:37 PM 5/16/2008, K & R Yoksh wrote:
> Hello Gene (and the list),
>Your question reminds me of a question I've been meaning to ask!
>My current S-band antenna is a simple integrated antenna/downconverter with
>123 MHz IF, but I plan to install a P3E-ready dish and downconverter on my
>crossboom this summer.
>My best downconverter is a K5GNA unit with 145 MHz IF. I wonder how it'll
>play on mode V/s? Can anyone comment on this?
>I also have some more 123 MHz IF units, but their NF is unknown. I'd rather
>use my AIDC 3731 from K5GNA, even if it means reduced performance on V/s. I
>plan to optimize for HEO operation, but I'd be happy if I could also work
>AO-51 in mode V/s.
Just a suggestion...
All downconverters will drift with temperature. The stock AIDC 3731
is spec'd to be within +/- 25 KHz over the temp range. I don't know
what the 145 MHz units are spec'd at but I doubt that it is better.
Other units I have seen are also around this figure and some are a
This is not much of a problem on AO-51 becuase there is a nice
strong carrier that is easy to find. On a linear passband like
P3E, it can be extremely difficult to find your own downlink
without QRMing the whole passband.
A better solution and the one that I use, is to put a low
noise preamp at the antenna and put your downconverter inside
your house where the temp is pretty stable. I have mine in the garage
which was fine for AO-40. Leaving the downconverter on all the time
is also helpful. On AO-40, my setup was more stable than the LO
on AO-40 and I could always hear my own downlink. I used InstantTune
(of course!) and loaded the parameters into the config file so it was
simple to just turn it on and work the sat. A fine tuning of around +/-1.5
was all that was needed to compensate for AO-40 LO drift.
I used an AIDC 3731 downconverter at 123 MHz which is pretty
sensitive but not as good as with the Down East Microwave 13ULNA preamp
which is really, really! good. A second advantage of using a preamp at the
antenna is that the downconverter sensitivity is then not very important
so you can use almost anything, even an old Drake unit.
If you have a really long run of coax, it might be cheaper to add a second
less expensive "booster" preamp and then use RG-6 coax from the preamp to
downconverter. I used LMR-600 because I wanted to be able to TX on it but
that is overkill for just receiving P3E.
Sent via AMSAT-BB at amsat.org. Opinions expressed are those of the author.
Not an AMSAT-NA member? Join now to support the amateur satellite program!
Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
More information about the AMSAT-BB